MANUFACTURING AND SPECIFICATIONS FOR GENERAL ASSEMBLY
In principle, all the kitchen, bar service and equipment by applying the latest developments in the technique, made of first quality materials and workmanship.Manufacturing base, after the plan before the general and special recipes in this specification will be the last.
DIMENSIONS
Specified in the project and the recipes are approximate and dimensions (cm) is shown.Given in recipes dimensions (Length x Depth x Height). Exact dimensions of the construction on site and will be tiles. Bar cabinets and refrigerators in six bench height of 55 and 80 cm in width. Are. Stainless Steel bench one-piece will return to their backs. All kitchen equipment used in AISI 304 stainless steel sheet 18/8 chrome-nickel-will.Specification specifies otherwise simply "Stainless Steel Plate" or "304 Quality Hair" referred to as.
Stainless steel sheet thicknesses as follows:
Naylonludur satin sheets and all.
All washing machines ..................................... worktop sinks 1.50 mm.
All work benches upper trays ............................................. .. 1.50 mm.
The base, intermediate shelves, upper shelves, grill shelves ....................................... 1:20mm.
Dual sliding doors, hinged doors ............................................ 1.00 mm ..
Side plates and trays .............................................. .......... 0.80-1.00 mm.
Hot cupboard, cold cabinet interior ........................................... ... 0.50 mm.
Will be thick.
CARCASS
Cooking units, cabinets, counters, and similar devices, 40 x 40, 40 x 20, 20 x 20 cm.'Black box of ready or suitable cross section profiles and L 30, L 40 brackets will be used. Other units
304 stainless steel sheet has been used to profile.
FEET AND FEEDS
Foot devices profiles, search by place of reinforcements and fittings 1.50 mm to 1:00.thick
Made of AISI 304 stainless steel sheet. Bench type devices foot profiles 40 x 40 x 1.2 mm.
will be shaped like an open box of stainless steel sheet and the end of the adjustable nylon 66 black hard plastic structure
will or aluminum lugs. Cabinet and similar devices (coated sides) 40 x 40 mm.
cross-section of 150 mm. high Cr - Ni kullanılacaktır.Tezgahlarda 2000 mm length up to 4 feet, 6 feet to above shall be used.
WELDING PROCESS AND APPEARANCE
All devices, sources of nickel chromium stainless steel electrodes, electric-arc, specific and / or argon arc welding will be applied. Satin tops and visible welds ground and will be introduced. Other surfaces will be left as natural and matte appearance.
Tops
Working bench tops with straight and 40 mm. - 20 mm. double-turn, washing and cleaning machines discount, and 40 mm. - 20 mm. will be double-turn. Bottom parts of Tables stainless steel according to the dimensions required and / or galvanized steel profiles and will be reinforced by welding. All tops with walls, columns from the rear and sides of places will be made uniform as a backing. Tables definitely 1.5 mm. and bottom thickness of galvanized profile will be put on the sound-absorbing reinforcement.
SINKS
As mentioned above, all the sinks and the tops of discount and 1.5 mm. thick stainless steel sheet will be made. Cuvettes used in standard sizes ready to die. Press the upper tray table sinks and bathtubs and 1.20 mm thick stainless steel sheet will be solid.
All washing machines appear lower and lateral sides of the sink - 1.00 mm to the depth of the garbage hopper. 'Of tin-coated stainless steel. This coating will be at the same time serve as reinforcements.
WORKTOP
Floor height 850 mm, 60 mm in wall-backed side, demand will be footed by the appropriate sub-table, and general recognition.
CABINET WORK BENCH
Floor height 850 mm, 60 mm in wall-backed side, the bottom plate, surrounded by a closed, according to the definition and general standing in front of the sliding door will be made, or multiplication.
SHELVING - WALL SHELVES
The base of all devices, shelves and wall shelves Search 1.20 mm. thick stainless steel sheet and will be produced as a double-turn. 1.20 mm grid type shelves. will be produced in a perforated stainless steel sheet. Wall consoles and racks on the wall of stainless steel brackets shall be fixed by fixing screws.
DOORS
Dual sliding doors, industrial nylon (N 66) and 1.00 mm roller. stainless steel sheet, double-turn and leave the hull will be manufactured as necessary, reinforcements will be taken back. Hinged doors hinges hinges shall be stainless steel or chrome steel bars.Food container and so on. covers 1.00 mm. and double-turn will be made.
DRAWERS
Caskets 1.00 mm. 50 x 40 x 12.5 cm thick stainless steel sheet. sizes will be produced from the internal net. Stainless steel profile sliding system on rails (N 66) roller bearing work. Self-giving for the drawer handles will form the cap. Where the key will be used in recipes. (Funds will be requested as well.) Mentioned in the bids will be produced if the size drawers gastronome.
MOVING UNITS
All mobile units, and according to the function instead of 100,125,150 mm. will be used throughout the heavy-duty wheels. Detection and removable solid structure, two brake wheels, they may turntable.
HOODS
TYPES
Medium type-V filter teams. Single-row filter type-suited Wall
METHOD OF MANUFACTURING
Argon determination will be made together with spot welding hood hair. Hair 1.00 mm.
18/8 Cr-Ni will be.
FILTERS
Filters with filter hoods stainless steel-framed wire or flame repellent hair grease filter shall be used. Filter according to dimensions of 50 x 50 x 4 cm. will. Mid-type hoods (V type) in two rows, one row of wall-mounted hoods, filtered and used enough. Mid-type hood (V) at the ends of the filter drain plug oil collection pipe under team (Tapa) will.
Wall mounted hoods hoods back hair, the lower channel will serve as the pan. Ends of the discharge pipe (Tapa) will be installed.
GRILLE
According to the measurements give the ventilation grilles contractor (exhaust outlets), the kitchen can be opened by the contractor.
DETERMINATION OF THE SYSTEM
Mid-type hoods can be adjusted ceiling with a special rope, wall-mounted hoods with rear dowel-screw will be hung in front of a special rope. Suspension wire rope shall be galvanized. Contractor the contract will be done by exhaust hoods connected to the duct.
LIGHTING EQUIPMENT
Fluorescent lamp mounting feet for hoods shall be specified. (Upon request)
Fitting and supply of fluorescent lamps and ready for electrical installation will be undertaken.
Cooling Unit
TYPE SIZE
Vertical height of the cold cabinets project. 80-85 and 100 cm in the horizontal cold-cabinet racks. in height. On other dimensions specified in recipes. (Or, in the dimension of the project.)
CARCASS
Refrigeration unit will be manufactured carcass, carcass profile and twice the boat - will be pulled varnish. 150 mm. ² 40x40 Cr - Ni profile in accordance with the feet connect to the closet.
ISOLATION
35-40 kg/m3 density polyurethane insulation.
COATING
Cold cabinet - machine tools complete interior and exterior will be coated AISI 304 stainless steel sheet.
DOORS
Isothermal structure and will be completely sealed. Unless otherwise specified in the descriptions of all-round rubber seal to prevent leakage at the door boat - varnish has been applied to the tapered beech slats used.
Hornbeam door moldings and doors used in both slot. All faces will be varnished.
Accept the withdrawal of lacquer strips on cabinet doors and freezers frost resistance edilmeyecektir.Derin done.
Kullanılacaktır.Kabin will be lit inside a special locking system on doors.
SHELF
Shelves of all cooling units 4 and 6 mm. 'To be manufactured of galvanized iron bars (white plastic) coated. Plastic coating will not appear in any way under the iron. Shelves are adjustable, and carriers are established.
EVAPORATOR
Cooler by the functionality of the units specified in the proposal, and sufficient capacity in the static or fan (airforce) used evaporators.
Defrost water in a pan with a pipe to be connected or cabinet akıtılacaktır below.
Compressor - condenser group
In short, "the group referred to as". Cell at the bottom of cabinet, the cabinet where the top or near the cell of another device that can be placed under the weather. The compressor and the electric motor, which is fully enclosed within the same body (hermetic) compressors, ie "ekovatlar" will be used. This ekovatlar
230 V, 50 Hz drafts will be building work. Ekovatlar forces will be selected according to the function.
Ekovatların relay, thermal protection, and capacities will be mounted on or in a separate box.
REFRIGERANT
All refrigeration units will be used as a refrigerant gas R134A or R404A. For all groups, filling the gas service valve gland or service will. To the gas filler pipe will be left long.R134A or R404A refrigerant liquid line drier units in all groups (dehumidifiers) must be used.
LABEL
All cold cupboards Ecowatt, condenser, and evaporator fan motor power will be a label.
COPPER PIPES
R134A or R404A refrigeration characteristics and soft copper tubes will be used in installations. At least 0.8 mm in thickness. must. Return line (R134A or R404A gas) pipes properly insulated with glass wool or rubber insulation will lozenges.
OTHER
On the basic properties of refrigerants other special recipes not listed here be stated.
WALL CABINETS
The size of the project is a top, a middle, and top plate around the sliding doors closed in front, intermediate and bottom plates of 1.2 mm. 0.8 mm in the environment. 18/8 Cr-Ni will be made from the hair.
Plastic or steel bolts shall be installed in the wall.
BAR FRIDGE bathtub
(Provided that the dimensions of the project)
The top plate of 1.5 mm. is backed with two or four on a one-piece aluminum can and bottle cooling eye bath available. Ice is available in base and a filter sump hole in the tub, separate soğutulacaktır with a serpentine system. Instead of going by the cabinet and the front of the bodies panjurla Ekovatlar closed. Other features are the same as explained in the section on the cooling cabinets.
INSTALLATION - MATCHING THE PLACEMENT
As indicated in the contract.
MATERIAL AND PLUMBING CONNECTIONS INSTALLATION
Hot and cold water, waste water, steam, condensate, LPG or coal gas, electricity and metered plans showing the points of the desired installation contractor shall be prepared by the kitchen. Installations until the desired points, and devices that will be brought by contractors on correlated. Other issues are listed below.
HOT - COLD WATER
All fittings are to be supplied by the contractor and shall be installed in the main installation.
SOFT WATER
All domestic and foreign devices connected to soft water. (Washing machines, coffee machines,
Ice machines v.b)
SEWAGE
Siphon and valve main installation by the contractor, shall be installed in the sink.
STEAM - Electrical
Atu 0.4 installation by the contractor on the main steam lines, steam and condensate will be brought up and connected devices. Bain marie made of stainless steel pipe coils, steam trap, strainer, check valve, steam valve up to the device, such as installation of equipment will be installed by the contractor. Kitchen contractor rather than simply place the device.
ELECTRIC
Related devices, electrical power and control lines to be brought by the electrical contractor, and the line of 1.5 m. Long enough to be dropped. On the device control panel, switch or button link to be made by the electrical contractor. But they will certainly not be the electrical device. The first study will be done by contractor for the kitchen.
German EGO brand thermostats will be used in electric devices.
LPG - GAS
LPG related to devices and / or natural gas lines and seamless steel pipe and the intermediate cut-off valves in accordance with the main installation project will be done by the contractor. Likewise, all kinds of LPG regulators, and provide for cost of hardware will be installed by a contractor for the kitchen. Contractor will be held under the supervision of the first ignition and work the kitchen. Compliance with relevant standards will be the responsibility of the construction of the tube with the tube room room kitchen contractor supplies construction and outside the tubes.
DIMENSIONS AND DETAILS OF MANUFACTURING
According to the measurements will be taken from a-Manufacturing. Specification and dimensions of the plan with the case of divergence between the manufacturing dimensions, the new measuring and manufacturing details of the project shall be attested by payers.
b-production measurements with the Specification and dimensions of a discrepancy between the plan and therefore require details of changing the approval of the project are necessary for the taxpayer.
This discrepancy; length 0.1 meters, 0.1 meters in depth the case of large, taxpayer-kitchen equipment contractor for the new price-controlled by the project must be determined before and fabrication.